View LT1302_110120.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT1302/LT1302-5 Micropower High Output Current Step-Up Adjustable and Fixed 5V DC/DC Converters
FEATURES
s s s s s s
DESCRIPTIO
s s
5V at 600mA or 12V at 120mA from 2-Cell Supply 200A Quiescent Current Logic Controlled Shutdown to 15A Low VCESAT Switch: 310mV at 2A Typical Burst ModeTM Operation at Light Load Current Mode Operation for Excellent Line and Load Transient Response Available in 8-Lead SO or PDIP Operates with Supply Voltage as Low as 2V
The LT(R)1302/LT1302-5 are micropower step-up DC/DC converters that maintain high efficiency over a wide range of output current. They operate from a supply voltage as low as 2V and feature automatic shifting between Burst Mode operation at light load, and current mode operation at heavy load. The internal low loss NPN power switch can handle current in excess of 2A and switch at frequencies up to 400kHz. Quiescent current is just 200A and can be further reduced to 15A in shutdown. Available in 8-pin PDIP or 8-pin SO packaging, the LT1302/ LT1302-5 have the highest switch current rating of any similarly packaged switching regulators presently on the market.
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATI
s s s s s
S
Notebook and Palmtop Computers Portable Instruments Personal Digital Assistants Cellular Telephones Flash Memory
Burst Mode is a trademark of Linear Technology Corporation.
TYPICAL APPLICATI
L1 10H
6 7 VIN SW PGND GND 1
NC 5 IT SHDN 3 4 SHUTDOWN
2-Cell to 5V Converter Efficiency
90 88 86
EFFICIENCY (%)
2 CELLS
+ C1
100F
C3 0.1F D1
LT1302-5 8 SENSE VC
84 82 80 78 76 74
+ C2
100F
2 RC 20k CC 0.01F
OUTPUT 5V 600mA C1 = C2 = SANYO OS-CON L1 = COILTRONICS CTX10-3 COILCRAFT DO3316-103
72
LT1302 * F01
70 1 10 100 LOAD CURRENT (mA) 1000
LT1302 * TA02
D1 = MOTOROLA MBRS130LT3
Figure 1. 2-Cell to 5V/600mA DC/DC Converter
U
VIN = 3V VIN = 2.5V VIN = 2V
UO
UO
1
LT1302/LT1302-5 ABSOLUTE AXI U RATI GS PACKAGE/ORDER I FOR ATIO
TOP VIEW GND 1 VC 2 SHDN 3 (SENSE*)FB 4 8 7 6 5 PGND SW VIN IT
VIN Voltage ............................................................. 10V SW Voltage ............................................................. 25V FB Voltage .............................................................. 10V SHDN Voltage ......................................................... 10V VC Voltage ................................................................ 4V IT Voltage .................................................................. 4V Maximum Power Dissipation ............................ 700mW Operating Temperature Range .................... 0C to 70C Storage Temperature Range ............... - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C
ORDER PART NUMBER LT1302CN8 LT1302CS8 LT1302CN8-5 LT1302CS8-5 S8 PART MARKING 1302 13025
N8 PACKAGE S8 PACKAGE 8-LEAD PDIP 8-LEAD PLASTIC SO *FIXED VERSION PINS 1 AND 8 ARE INTERNALLY CONNECTED IN SOIC PACKAGE
TJMAX = 125C, JA = 100C/W (N8) TJMAX = 125C, JA = 80C/W (S8)
Consult factory for Industrial and Military grade parts.
DC ELECTRICAL CHARACTERISTICS
SYMBOL IQ VIN VFB PARAMETER Quiescent Current Input Voltage Range
TA = 25C, VIN = 2.5V, unless otherwise noted.
MIN
q q q
CONDITIONS VSHDN = 0.5V, VFB = 1.3V VSHDN = 1.8V
TYP 200 15
MAX 300 25 8 1.26 5.25
VOS
Feedback Voltage (LT1302) Feedback Pin Bias Current (LT1302) Output Sense Voltage (LT1302-5) Output Ripple Voltage (LT1302-5) Sense Pin Resistance to Ground (LT1302-5) Offset Voltage Comparator Hysteresis Oscillator Frequency Maximum Duty Cycle Switch On Time Switch Off Time Output Line Regulation Switch Saturation Voltage Switch Leakage Current Switch Current Limit Error Amplifier Voltage Gain Shutdown Pin High Shutdown Pin Low Shutdown Pin Bias Current
VC = 0.4V VFB = 1V VC = 0.4V VC = 0.4V See Block Diagram (Note 1) Current Limit Not Asserted (Note 2)
q q
2.0 2.2 1.22 4.85
q
DC tON tOFF VCESAT
175 160 75
1.24 100 5.05 50 420 15 5 220 86 3.9 0.7 0.06 310 0.1 1 2.8 75
265 310 95
Current Limit Not Asserted 2 < VIN < 8V ISW = 2A VSW = 5V, Switch Off VC = 0.4V (Burst Mode Operation) VC = 1.25V (Full Power) (Note 3) 0.9V VC 1.2V, VC/VFB
q q q q q q
0.15 400 475 10 3.9
VSHDNH VSHDNL ISHDN
2.0 50 1.8
VSHDN = 5V VSHDN = 2V VSHDN = 0V
q q
I T Pin Resistance to Ground The q denotes specifications which apply over the 0C to 70C temperature range. Note 1: Hysteresis is specified at DC. Output ripple depends on capacitor size and ESR.
8 3 0.1 3.9
0.5 20 1
UNITS A A V V V nA V mV k mV mV kHz kHZ % s s %/V mV mV A A A V/ V V V A A A k
Note 2: The LT1302 operates in a variable frequency mode. Switching frequency depends on load inductance and operating conditions and may be above specified limits. Note 3: Minimum switch current 100% tested. Maximum switch current guaranteed by design.
2
U
W
U
U
WW
W
LT1302/LT1302-5 TYPICAL PERFORMANCE CHARACTERISTICS
No-Load Quiescent Current Circuit of Figure 1
500 450
QUIESCENT CURRENT (A)
TA = 25C 500 400
350 300 250 200 150 100 50 0 2.0
SATURATION VOLTAGE (mV)
400
VCESAT (V)
2.5
3.0 3.5 4.0 SUPPLY VOLTAGE (V)
LT1302 Feedback Voltage
1.250 1.245 600 500
1.235 1.230 1.225 1.220 1.215 1.210 1.205 1.200 -50 -25 0 25 50 TEMPERATURE (C) 75 100
QUIESCENT CURRENT (A)
SENSE RESISTANCE (k)
1.240 FEEDBACK VOLTAGE (V)
Error Amplifier Offset Voltage
30 25
OFFSET VOLTAGE (mV)
OUTPUT VOLTAGE (V)
5.025 5.000 4.975 4.950 4.925 4.900 -50 -25 0 25 50 TEMPERATURE (C) 75 100
ON-TIME (s)
20 15 10 5 0 -50
-25
0 25 50 TEMPERATURE (C)
UW
4.5
1302 G01
1302 G04
Switch Saturation Voltage
600 TA = 25C
350 300 250 200 150 400
Switch Saturation Voltage
ISW = 2A
300 200 100 0
5.0
0
1 2 3 SWITCH CURRENT (A)
4
1302 G02
100 -50
-25
0 25 50 TEMPERATURE (C)
75
100
1302 G03
LT1302-5 Sense Pin Resistance
300 250 200 150 100 50
Quiescent Current
VIN = 2.5V SWITCH OFF
400 300 200 100 0 -50
-25
0 25 50 TEMPERATURE (C)
75
100
0 -50
-25
0 25 50 TEMPERATURE (C)
75
100
1302 G05
1302 G06
LT1302-5 Output Voltage
5.100 5.075 5.050 4.0 3.5 3.0 2.5 5.0 4.5
Maximum On-Time
75
100
2.0 -50
-25
0 25 50 TEMPERATURE (C)
75
100
1302 G07
1302 G08
1302 G09
3
LT1302/LT1302-5 TYPICAL PERFORMANCE CHARACTERISTICS
Maximum Duty Cycle
100 300 275
SHUTDOWN CURRENT (A) FREQUENCY (kHz)
90
DUTY CYCLE (%)
80
70
60
50 -50
-25
0 25 50 TEMPERATURE (C)
LT1302-5 Output Voltage vs Load Current
5.20 5.15
20
OUTPUT VOLTAGE (V)
5.05 5.00 4.95 4.90 VIN = 2.2V VIN = 4V VIN = 3V
OUTPUT POWER (W)
5.10
4.85 4.80 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 LOAD CURRENT (A)
1302 G13
PI FU CTIO S
GND (Pin 1): Signal Ground. Feedback resistor and 0.1F ceramic bypass capacitor from VIN should be connected directly to this pin. VC (Pin 2): Frequency Compensation Pin. Connect series RC to GND. Keep trace short. SHDN (Pin 3): Shutdown. Pull high to effect shutdown; tie to ground for normal operation. FB/Sense (Pin 4): Feedback/Sense. On the LT1302 this pin connects to CMP1 input. On the LT1302-5 this pin connects to the output resistor string. IT (Pin 5): Normally left floating. Addition of a 3.3k resistor to GND forces the LT1302 into current mode at light loads. Efficiency drops at light load but increases at medium loads. See Applications Information section. VIN (Pin 6): Supply Pin. Must be bypassed with: (1) a 0.1F ceramic to GND, and (2) a large value electrolytic to PGND. When VIN is greater than 5V, a low value resistor (2 to 10) is recommended to isolate the VIN pin from input supply noise.
4
UW
75
1302 G10
Oscillator Frequency
20 18 16 14 12 10 8 6 4 2
Shutdown Pin Bias Current
TA = 25C
250 225 200 175 150 -50
100
-25
0 25 50 TEMPERATURE (C)
75
100
0 0 1 6 4 2 3 5 SHUTDOWN VOLTAGE (V) 7 8
1302 G11
1302 G12
Maximum Output Power* Boost Mode
16
12
8
4
0 0 2 6 4 INPUT VOLTAGE (V) 8 10
1302 G14
* APPROXIMATE
U
U
U
LT1302/LT1302-5
PI FU CTIO S
SW (Pin 7): Switch Pin. Connect inductor and diode here. Keep layout short and direct. PGND (Pin 8): Power Ground. Pins 8 and 1 should be connected under the package. In the SO package, pins 1 and 8 are thermally connected to the die. One square inch of PCB copper provides an adequate heat sink for the device.
BLOCK DIAGRA SM
L1 VIN C1 D1
+
6 VIN
1.24V REFERENCE
R1 4 C5 100pF R2
FB VOS 15mV
SHDN 3 SHUTDOWN
W
U
U
U
C2 0.1F 7 SW
+
VOUT C3
36mV
+
A2
R4 1.75 R5 730
- + -
CMP1 ENABLE OFF 220kHz OSCILLATOR
A3 DRIVER
Q3
Q4 160X
HYSTERETIC COMPARATOR 2A VIN Q5 VIN Q1 ERROR AMPLIFIER 300 Q2
-
A1
BIAS
+
3.6k
1
GND
2
VC R3 22k C4 0.01F
5
IT
8
PGND
1302 F02
Figure 2. LT1302 Block Diagram
5
LT1302/LT1302-5
BLOCK DIAGRA SM
SENSE 4 VIN 6 SW 7
R1 315k 1.24V REFERENCE
R2 105k
SHDN
3
SHUTDOWN
1 GND
OPERATIO
The LT1302's operation can best be understood by examining the block diagram in Figure 2. The LT1302 operates in one of two modes, depending on load. With light loads, comparator CMP1 controls the output; with heavy loads, control is passed to error amplifier A1. Burst Mode operation consists of monitoring the FB pin voltage with hysteretic comparator CMP1. When the FB voltage, related to the output voltage by external attenuator R1 and R2, falls below the 1.24V reference voltage, the oscillator is enabled. Switch Q4 alternately turns on, causing current buildup in inductor L1, then turns off, allowing the built-up current to flow into output capacitor C3 via D1. As the output voltage increases, so does the FB voltage; when it exceeds the reference plus
6
W
36mV
+
A2
R4 1.75 R5 730
- + -
VOS 15mV CMP1 ENABLE OFF 220kHz OSCILLATOR
A3 DRIVER
Q3
Q4 160X
HYSTERETIC COMPARATOR 2A VIN Q5 VIN Q1 ERROR AMPLIFIER 300 Q2
-
A1
BIAS
+
3.6k
2 VC
5 IT
8 PGND
1302 F03
Figure 3. LT1302-5 Block Diagram
U
CMP1's hysteresis (about 5mV) CMP1 turns the oscillator off. In this mode, peak switch current is limited to approximately 1A by A2, Q2, and Q3. Q2's current, set at 34A, flows through R5, causing A2's negative input to be 25mV lower than VIN. This node must fall more than 36mV below VIN for A2 to trip and turn off the oscillator. The remaining 11mV is generated by Q3's current flowing through R4. Emitter-area scaling sets Q3's collector current to 0.625% of switch Q4's current. When Q4's current is 1A, Q3's current is 6.25mA, creating an 11mV drop across R4 which, added to R5's 25mV drop, is enough to trip A2. When the output load is increased to the point where the 1A peak current cannot support the output voltage,
LT1302/LT1302-5
OPERATIO
CMP1 stays on and the peak switch current is regulated by the voltage on the VC pin (A1's output). VC drives the base of Q1. As the VC voltage rises, Q2 conducts less current, resulting in less drop across R5. Q4's peak current must then increase in order for A2 to trip. This current mode control results in good stability and immunity to input voltage variations. Because this is a linear,
APPLICATIONS INFORMATION
Inductor Selection Inductors used with the LT1302 must fulfill two requirements. First, the inductor must be able to handle current of 2.5A to 3A without runaway saturation. Rod or drum core units usually saturate gradually and it is acceptable to exceed manufacturers' published saturation currents by 20% or so. Second, it should have low DCR, under 0.05 so that copper loss is kept low. Inductance value is not critical. Generally, for low voltage inputs down to 2V, a 10H inductor is recommended (such as Coilcraft DO3316103). For inputs above 4V to 5V use a 22H unit (such as Coilcraft DO3316-223). Switching frequency can reach up to 400kHz so the core material should be able to handle high frequency without loss. Ferrite or molypermalloy cores are a better choice than powdered iron. If EMI is a concern a toroidal inductor is suggested, such as Coiltronics CTX20-4. For a boost converter, duty cycle can be calculated by the following formula:
L
V DC = 1- IN VOUT
A special situation exists where the VOUT/VIN differential is high, such as a 2V-to-12V converter. The required duty cycle is higher than the LT1302 can provide, so the converter must be designed for discontinuous operation. This means that inductor current goes to zero during the switch off-time. In the 2V-to-12V case, inductance must be low enough so that current in the inductor can reach 2A in a single cycle. Inductor value can be defined by:
U
W
U
U
U
closed-loop system, frequency compensation is required. A series RC from VC to ground provides the necessary pole-zero combination. The LT1302-5 incorporates feedback resistors R1 and R2 into the device. Output voltage is set at 5.05V in Burst Mode, dropping to 4.97V in current mode.
(V
IN - VSW
)x t
ON
2A
With the 2V input a value of 3.3H is acceptable. Since the inductance is so low, usually a smaller core size can be used. Efficiency will not be as high as for the continuous case since peak currents will necessarily be higher. Table 1 lists inductor suppliers along with appropriate part numbers.
Table 1. Recommended Inductors
VENDOR Coilcraft PART NO. DO3316-103 DO3316-153 DO3316-223 CTX10-2 CTX20-4 LPT4545-100LA LPT4545-200LA CD105-100 CD105-150 CDR125-220 VALUE(H) 10 15 22 10 20 10 20 10 15 22 PHONE NO. (708) 639-6400
Coiltronics Dale Sumida
(407) 241-7876 (605) 665-9301 (708) 956-0666
Capacitor Selection The output capacitor should have low ESR for proper performance. A high ESR capacitor can result in "modehopping" between current mode and Burst Mode at high load currents because the output voltage will increase by ISW x ESR when the inductor current is flowing into the diode. Figure 4 shows output voltage of an LT1302-5 boost converter with two 220F AVX TPS capacitors at the output. Ripple voltage at a 510mA load is about 30mVP-P
7
LT1302/LT1302-5
APPLICATIONS INFORMATION
and there is no low frequency component. The total ESR is under 0.03. If a single 100F aluminum electrolytic capacitor is used instead, the converter mode-hops between current mode and Burst Mode due to high ESR, causing the voltage comparator to trip as shown in Figure 5. The ripple voltage is now over 500mVP-P and contains a low frequency component. Maximum allowable output capacitor ESR can be calculated by the following formula: ESRMAX = VOS x VOUT VREF x 1A Input Capacitor The input supply should be decoupled with a good quality electrolytic capacitor close to the LT1302 to provide a stable input supply. Long leads or traces from power source to the switcher can have considerable impedance at the LT1302's switching frequency. The input capacitor provides a low impedance at high frequency. A 0.1F ceramic capacitor is required right at the VIN pin. When the input voltage can be above 5V, a 10/1F decoupling network for VIN is recommended as detailed in Figure 6. This network is also recommended when driving a transformer.
VIN > 5V 10
where, VOS = 15mV VREF = 1.24V
VOUT 50mV/DIV AC COUPLED
ILOAD
510mA 10mA
500s/DIV
1302 F04
Figure 4. Low ESR Output Capacitor Results in Stable Operation. Ripple Voltage is Under 30mVP-P
VOUT 200mV/DIV AC COUPLED
510mA ILOAD 10mA
500s/DIV
1302 F05
Figure 5. Inexpensive Electrolytic Capacitor Has High ESR, Resulting in Mode-Hop, Ripple Voltage Amplitude Is Over 500mVP-P and Includes Low Frequency Component
8
U
W
U
U
VIN
SW
+
47F TO 100F
+
1F LT1302 GND PGND
1302 F06
***
Figure 6. A 10/1F Decoupling Network at VIN Is Recommended When Input Voltage Is Above 5V
Table 2 lists capacitor vendors along with device types.
Table 2. Recommended Capacitors
VENDOR AVX Sanyo Sprague SERIES TPS OS-CON 595D TYPE Surface Mount Through Hole Surface Mount PHONE NO. (803) 448-9411 (619) 661-6835 (603) 224-1961
Diode Selection A 2A Schottky diode such as Motorola MBRS130LT3 has been found to be the best available. Other choices include 1N5821 or MBRS130T3. Do not use "general purpose" diodes such as 1N4001. They are much too slow for use in switching regulator applications.
LT1302/LT1302-5
APPLICATIONS INFORMATION
Frequency Compensation Obtaining proper RC values for the frequency compensation network is largely an empirical procedure, since variations in input and output voltage, topology, capacitor ESR and inductance make a simple formula elusive. As an example, consider the case of a 2.5V to 5V boost converter supplying 500mA. To determine optimum compensation, the circuit is built and a transient load is applied to the circuit. Figure 7 shows the setup. In Figure 7a, the VC pin is simply left floating. Although output voltage is maintained and transient response is good, switch current rises instantaneously to the internal current limit upon application of load. This is an undesirable situation as it places maximum stress on the switch and the other power components. Additionally, efficiency is well down from its optimal value. Next, a 0.1F capacitor is connected with no resistor. Figure 7b details response. Although the circuit eventually stabilizes, the loop is quite underdamped. Initial output "sag" exceeds 5%. Aberrant
VIN 2.5V L1 10H
+
C1 330F
D1
+
C2 220F
+
C3 220F
C1, C2, C3 = AVX TPS SERIES D1 = MOTOROLA MBRS130LT3 L1 = COILCRAFT DO3316-103K
Figure 7. Boost Converter with Simulated Load
VOUT 100mV/DIV AC COUPLED
510mA ILOAD 10mA 2ms/DIV
1302 F07a
Figure 7a. VC Pin Left Unconnected. Output Shows Low Frequency Components Under Load
U
W
U
U
behavior in the 4th graticule is the result of the LT1302's Burst Mode comparator turning off all switching as output voltage rises above its threshold. In Figure 7c, the 0.1F capacitor has been replaced by a 0.01F unit. Undershoot is less but the response is still underdamped. Figure 7d shows the results of the 0.1F capacitor and a 10k resistor in series. Now some amount of damping is observed, and behavior is more controlled. Figure 7e details response with a 0.01F/10k series network. Undershoot is down to around 100mV, or 2%. A slight underdamping is still noticeable. Finally, a 0.01F/24k series network results in the response shown in Figure 7f. This has optimal damping, undershoot less than 100mV and settles in less than 1ms. The VC pin is sensitive to high frequency noise. Some layouts may inject enough noise to modulate peak switch current at 1/2 the switching frequency. A small capacitor connected from VC to ground will eliminate this. Do not exceed 1/10 of the compensation capacitor value.
NC
VIN SW 0.1F PGND GND
IT SHDN
LT1302-5 SENSE VC R C MTP3055EL 50
1302 F07
500
10 2W PULSE GENERATOR
VOUT 100mV/DIV AC COUPLED 510mA ILOAD 10mA 2ms/DIV
1302 F07b
Figure 7b. 0.1F from VC to Ground. Better, but More Improvement Needed
9
LT1302/LT1302-5
APPLICATIONS INFORMATION
VOUT 100mV/DIV AC COUPLED
ILOAD
510mA 10mA 2ms/DIV
1302 F07c
Figure 7c. 0.01F from VC to Ground. Underdamped Response Requires Series R
VOUT 100mV/DIV AC COUPLED
510mA ILOAD 10mA 2ms/DIV
1302 F07d
Figure 7d. 0.1F with 10k Series RC. Classic Overdamped Response
VOUT 100mV/DIV AC COUPLED
510mA ILOAD 10mA
2ms/DIV
1302 F07e
Figure 7e. 0.01F, 10k Series RC Shows Good Transient Response. Slight Underdamping Still Noticeable
VOUT 100mV/DIV AC COUPLED
ILOAD
510mA 10mA 2ms/DIV
1302 F07f
Figure 7f. 0.01F, 24k Series RC Results in Optimum Response
10
U
W
U
U
IT Pin The IT pin is used to disable Burst Mode, forcing the LT1302 to operate in current mode even at light load. To disable Burst Mode, 3.3k resistor R1 is connected from IT to gound. More conservative frequency compensation must be used when in this mode. A 0.1F capacitor and 4.7k resistor from VC to ground has been found to be adequate. Low frequency Burst Mode ripple can be reduced or eliminated using this technique in many applications. To illustrate, the transient load response of Figure 8's circuit is pictured without and with R1. Figure 8a shows output voltage and inductor current without the resistor. Note the 6kHz burst rate when the converter is delivering 25mA. By adding the 3.3k resistor, the low frequency bursting is eliminated, as shown in Figure 8b. This feature is useful in systems that contain audio circuitry. At very light or zero load, switching frequency drops and eventuVIN 2.5V 10H
+
VIN C1 330F SW MBRS130LT3 0.1F
SENSE
LT1302-5 PGND GND VC IT R1 3.3k
1302 F08
+
220F 10V
+
220F 10V
4.7k 0.1F
VOUT 5V 600mA
Figure 8. Addition of R1 Eliminates Low Frequency Output Ripple in This 2.5V to 5V Boost Converter
VOUT 100mV/DIV AC COUPLED INDUCTOR CURRENT 1A/DIV ILOAD 525mA 25mA 1ms/DIV
1302 F08a
Figure 8a. IT Pin Floating. Note 6kHz Burst Rate at ILOAD = 25mA. 0.1F/4.7k Compensation Network Causes 220mV Undershoot
LT1302/LT1302-5
APPLICATIONS INFORMATION
ally reaches audio frequencies, but at a much lighter load than without the IT feature. At some input voltage/load current combinations, some residual bursting may occur at frequencies out of the audio band.
VOUT 100mV/DIV AC COUPLED
INDUCTOR CURRENT 1A/DIV 525mA ILOAD 25mA 1ms/DIV
1302 F08b
Figure 8b. 3.3k Resistor from IT Pin to Ground Forces LT1302 into Current Mode Regardless of Load. Audio Frequency Component Eliminated
90 80
EFFICIENCY (%)
IT FLOATING
70 60 50 40 30
3.3k IT TO GND
1
10 100 OUTPUT CURRENT (mA)
1000
1302 F08c
Figure 8c. 3.3k Resistor for IT to Ground Increases Efficiency at Moderate Load, Decreases at Light Load
VIN R2 C3 L1 R3 2 5 6 LT1302 C1 D1 C2 VOUT GND (BATTERY AND LOAD RETURN) 7 8 2 1 4 3 R1 200pF RC SHUTDOWN
+
+
Figure 9. Suggested Component Placement for LT1302
U
W
U
U
The IT pin cannot be used as a soft-start. Large capacitors connected to the pin will cause erratic operation. If operating the device in Burst Mode, let the pin float. Keep high dV/dt signals away from the pin. Figure 8c details efficiency with and without the addition of R1. Burst Mode operation keeps efficiency high at light load with IT floating. Efficiency falls off at light load with R1 added because the LT1302 cannot transition into Burst Mode. Layout The high speed, high current switching associated with the LT1302 mandates careful attention to layout. Follow the suggested component placement in Figure 9 for proper operation. High current functions are separated by the package from sensitive control functions. Feedback resistors R1 and R2 should be close to the feedback pin (pin4). Noise can easily be coupled into this pin if care is not taken. A small capacitor (100pF to 200pF) from FB to ground provides a high frequency bypass. If the LT1302 is operated off a three-cell or higher input, R3 (2 to 10) in series with VIN is recommended. This isolates the device from noise spikes on the input supply. Do not put in R3 if the device must operate from a 2V input, as input current will cause the voltage at the LT1302's VIN pin to go below 2V. The 0.1F ceramic bypass capacitor C3 (use X7R, not Z5U) should be mounted as close as possible to the package. When R3 is used, C3 should be a 1F tantalum unit. Grounding should be segregated as illustrated. C3's ground trace should not carry switch current. Run a
CC
1302 F09
11
LT1302/LT1302-5
APPLICATIONS INFORMATION
separate ground trace up under the package as shown. The battery and load return should go to the power side of the ground copper. Thermal Considerations The LT1302 contains a thermal shutdown feature which protects against excessive internal (junction) temperature. If the junction temperature of the device exceeds the protection threshold, the device will begin cycling between normal operation and an off state. The cycling is not harmful to the part. The thermal cycling occurs at a slow rate, typically 10ms to several seconds, which depends on the power dissipation and the thermal time constants of the package and heat sinking. Raising the ambient temperature until the device begins thermal shutdown gives a good indication of how much margin there is in the thermal design. For surface mount devices heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Experiments have shown that the heat spreading copper layer does not need to be electrically connected to the tab of the device. The PCB material can be very effective at transmitting heat between the pad area attached to pins 1 and 8 of the device, and a ground or power plane layer either inside or on the opposite side of the board. Although the actual thermal resistance of the PCB material is high, the length/area ratio of the thermal resistance between the layer is small. Copper board stiffeners and plated through holes can also be used to spread the heat generated by the device. Table 3 lists thermal resistance for the SO package. Measured values of thermal resistance for several different board sizes and copper areas are listed for each surface mount package. All measurements were taken in still air on 3/32" FR-4 board with 1oz copper. This data can be used as a rough guideline in estimating thermal resistance. The thermal resistance for each application will be affected by thermal interactions with other components as well as board size and shape.
Table 3. S8 Package, 8-Lead Plastic SO
COPPER AREA TOPSIDE* BACKSIDE BOARD AREA 2500 sq. mm 2500 sq. mm 2500 sq. mm 1000 sq. mm 2500 sq. mm 2500 sq. mm 225 sq. mm 100 sq. mm 100 sq. mm 100 sq. mm 100 sq. mm 2500 sq. mm 2500 sq. mm 2500 sq. mm 2500 sq. mm 1000 sq. mm 2500 sq. mm 225 sq. mm 100 sq. mm 2500 sq. mm 2500 sq. mm THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 60C/W 62C/W 65C/W 69C/W 73C/W 80C/W 83C/W
12
U
W
U
U
* Pins 1 and 8 attached to topside copper N8 Package, 8-Lead DIP: Thermal Resistance (Junction-to-Ambient) = 100C/W
Calculating Temperature Rise Power dissipation internal to the LT1302 in a boost regulator configuration is approximately equal to:
2 V V 2 OUT + VD OUT + VD - PD = IOUT R IOUT VOUT R V - IOUT VOUT R VIN - IN VIN VIN
+
IOUT VOUT + VD - VIN 27
(
)
The first term in this equation is due to switch "onresistance." The second term is from the switch driver. R is switch resistance, typically 0.15. VD is the diode forward drop. The temperature rise can be calculated from: T = PD x JA where: T = Temperature Rise PD = Device Power Dissipation JA = Thermal Resistance (Junction-to-Ambient)
LT1302/LT1302-5
APPLICATIONS INFORMATION
As an example, consider a boost converter with the following specifications: VIN = 3V VOUT = 6V IOUT = 700mA Total power loss in the LT1302, assuming R = 0.15 and VD = 0.45V, is:
2 0.7 6 + 0.45 - 3 6 + 0.45 6 + 0.45 0.15 - + 27 3 - 0.7 x 6 x 0.15 3 - 0.7 x 6 x 0.15 3 3
PD = 700mA
(
)(
2
)
= 223mW + 89mW = 312mW
Using the CS8 package with 100 sq. mm topside and backside heat sinking: T = (312mW)(84C/W) = 25.9C rise With the N8 package: T = 31.2C At a 70C ambient, die temperature would be 101.2C.
U
W
U
U
( )(
)
13
LT1302/LT1302-5
TYPICAL APPLICATIONS
Single Cell to 5V/150mA Converter
5V/150mA OUTPUT L1 3.3H 220 1.5V CELL 100k IL SET VIN SW1 AO SW2 VIN SW IT PGND SHDN FB 56.2k 1% 100pF 20k 4.99k 1% 36.5k 1% D1
LT1073 FB GND
L1 = COILCRAFT DO3316-332 D1 = MOTOROLA MBRS130LT3
2 CELLS
+ C1
100F
OUTPUT 12V 120mA C1 = AVX TPSD107M010R0100 C2 = AVX TPSD336M025R0200
14
U
10
100k
R1 301k 1% 2N3906 (169k FOR 3.3V) 100k
LT1302 VC GND
+
C1 47F
C2 220F
+
0.1F 0.01F
C1 = AVX TPSD476M016R0150 C2 = AVX TPSE227M010R0100
COILCRAFT (708) 639-2361
1302 TA03
2V to 12V/120mA Converter
L1 3.3H 7 C3 0.1F D1 8
6 VIN SW PGND GND 1
NC 5 IT SHDN 3 4 SHUTDOWN
LT1302 FB VC
+ C2
33F
+ C2
33F
2 RC 20k CC 0.02F
R1 100k 1%
100pF
R2 866k 1%
LT1302 * TA04
D1 = MOTOROLA MBRS130LT3 L1 = COILCRAFT DO3316-332
LT1302/LT1302-5
TYPICAL APPLICATIONS
3 Cell to 3.3V Buck-Boost Converter with Auxiliary 12V Regulated Output
VIN 2.5V-8V 10 SHUTDOWN 7 T1D 4 SHDN FB 100k 1% LT1302 VC GND IT PGND VIN SW 0.1F 6 T1E 5 D2 13V
169k 1%
200pF
24k 3 4700pF T1C 8 1
T1 = D1, D2 = C1 = C2 = C3 =
DALE LPE-6562-A069, 1:3:1:1:1 TURNS RATIO, 10H PRIMARY. DALE (605) 665-9301 MOTOROLA MBRS130LT3 AVX TPSE107016R0100 AVX TPSE337006R0100 AVX TPSD476016R0150
VIN 4V TO 9V
+
C1 100F 16V
L1, L2=COILCRAFT DO3316-223 C1=AVX TPSE107016R0100 C2, C3=AVX TPSE227010R0100
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
+ C3
47F 16V
+ C1
100F 16V D1
2 T1B 9 IN
+ 22F
25V LT1121 SHDN GND
OUT 330k 1% ADJ 150k 1%
12V 120mA
+
3.3F
+ C2
330F 6.3V
T1A 10
1302 TA05
3.3V OUTPUT 400mA
2 Li-Ion Cell to 5.8V/600mA DC/DC Converter
C2 220F 10V
L1 22H 10
+
+
1F
VIN IT LT1302 SHDN GND SHUTDOWN
SW FB
365k 1%
L2 22H
MBRS130LT3 VOUT 5.8V 600mA
VC PGND
+
20k 10nF VOUT VIN + VOUT 100k 1%
C3 220F 10V
DUTY CYCLE =
1302 TA07
PEAK SWITCH VOLTAGE = VIN + VOUT
15
LT1302/LT1302-5
PACKAGE DESCRIPTION
0.300 - 0.325 (7.620 - 8.255)
0.009 - 0.015 (0.229 - 0.381)
(
+0.025 0.325 -0.015 8.255 +0.635 -0.381
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTURSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm).
0.010 - 0.020 x 45 (0.254 - 0.508) 0.008 - 0.010 (0.203 - 0.254)
0- 8 TYP
0.016 - 0.050 0.406 - 1.270
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
16
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
U
Dimensions in inches (millimeters) unless otherwise noted. N8 Package 8-Lead Plastic DIP
0.400* (10.160) MAX 8 7 6 5
0.255 0.015* (6.477 0.381)
1
2
3
4
0.045 - 0.065 (1.143 - 1.651)
0.130 0.005 (3.302 0.127)
0.065 (1.651) TYP 0.125 (3.175) MIN 0.018 0.003 (0.457 0.076) 0.015 (0.380) MIN
)
0.045 0.015 (1.143 0.381) 0.100 0.010 (2.540 0.254)
N8 0694
S8 Package 8-Lead Plastic SOIC
0.189 - 0.197* (4.801 - 5.004) 8 7 6 5
0.228 - 0.244 (5.791 - 6.197)
0.150 - 0.157* (3.810 - 3.988)
1
2
3
4
0.053 - 0.069 (1.346 - 1.752)
0.004 - 0.010 (0.101 - 0.254)
0.014 - 0.019 (0.355 - 0.483)
0.050 (1.270) BSC
SO8 0294
LT/GP 0295 10K * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1995

▲Up To Search▲

Price & Availability of LT1302

	To Download LT1302 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .